Browse by category Quicklinks

Selected Case Study

 SCR Technology for University College London
Found under
Silencers, Indu...

IMS were awarded a contract in 2016 for the Design, Manufacture and Supply of an SCR Reactor combined with an acoustic housing suitable of reducing NOx emissions in the order of -80% while achieving noise levels of no more that 75dB(A) at 1mtr.

The photograph below shows the SCR Reactor with built in silencing being lifted to the roof area on a skid at University College London to be installed on top of the existing generator canopy.

The combined SCR + Silencer was to replace the existing silencer on the MTU 16V2000-G3 engine on the standby generator.

Details of the MTU 16V2000-G3 Engine:

Engine Type:                 MTU20V4000G23 (4-cycle, T/C, A/C)

Fuel Type:                    Diesel Powered (EN590)

Configuration:               V20

Engine Capacity:           94.4 Ltr

Bore and Stroke:           170mm x 210mm

Compression Ratio:       16.4:1

Rated Speed:                1500rpm

Power Rating:               2200 Kw (Prime)

Power Rating:               2420 Kw (Standby)

Electrical Rating:           2500 KVA (Prime)

Electrical Rating:           2800 KVA (Prime)

Exhaust Flow:               633.7 m3/s

Exhaust Temp:              550C

Fuel Consumption:        633.7 l/h at 100% Prime Power

AdBlue Consumption:    38 l/h at 100% Prime Power

Exhaust Back Pressure: 85mbar

Existing Noise Level:     85Dba@1M

The existing silencer was removed from the generator canopy roof and replaced by the combined SCR pus silencer.

The recommendation was to use no more than 50ppm ULSD Fuels to minimise any increase in particulates.

There was no stated requirement for the reductions in particulate, although it was not expected that we would increase PM as a result of introducing the SCR Technology.

Opacity measurements were taken following installation and it was found that there was no significant difference in the PM measurements mainly due to switching to the ULSD.

The specification called for reductions in CO (Carbon Monoxides) from 650mg/Nm3 to no more than 156mg/Nm3 and HC (Hydrocarbons) from 150mg/Nm3 to no more than 36mg/Nm3.

The actual CO results measured after the abatement was fitted was 130mg/Nm3 (reduction of -80%) and HC 30MG/Nm3 (again a reduction of -80%).

This was achieved by using a DOC catalyst up front to the SCR Substrates

The measured NOx levels on this engine prior to fitment of the IMS SCR Abatement Technology was 3500mg/m3N @ 5% O2 which was needed to be reduced to a maximum of 700mg/m3N @ 5% O2, a reduction factor of 80%.

The SCR system was designed to provide a reduction of a minimum of at least -85%, however when commissioned the actual NOx emissions were shown to be around 350mg/m3N @ 5% O2 which equates to a 90% reduction in NOx.

An AdBlue Tank of approximately 120 Ltr capacity was supplied together with transfer pipework which was suitable for a run-time of approximately 30 hrs at full load. Due to space restrictions a larger tank could not be installed, and the urea supplier had to guarantee to top up within 24 hours.

The SCR Substrates used were rectangular in shape fitted in a number of banks in series. Since supplying this type of system IMS have switched to using round substrates in a modular construction all in parallel which reduces the overall backpressure across the system.

This unit also had an external AdBlue Mixing Pipe which increases the length of the system. IMS now wherever possible uses an embedded mixer pipe with the reactor.

Also, the reactor used an air assisted AdBlue Injector which required a compressor to deliver the AdBlue and keep the injector cool.

Today, IMS uses an airless AdBlue injection system where the injector is cooled by recirculating the AdBlue across the injector.

We also now use both “Engine Out” and “Tailpipe” NOx Sensors (rather than a single NOx sensor on the outlet) as part of a closed loop system which continually monitors NOx reductions across the SCR Catalysts.

The complete system was delivered, installed and commissioned by IMS.

Telephone
+44 (0)1509 506792
Website
Address
IMS, Units 18-20 Gelders Halls Road, Shepshed, Leicestershire, LE12 9NH
View in Google Maps

Other Case Studies from this Company

Targeted Frequency Acoustic Project Targeted Frequency Acoustic Project
We recently completed this stunning acoustic project based at a utility company in the UK. Our ch...
SCR System for a Hospital in London SCR System for a Hospital in London
After creating the SCR system bespoke, our expert installation team began installing the SCR syst...
Bespoke Chimney & Pipework Project Bespoke Chimney & Pipework Project
We designed, manufactured, delivered & site supervised this chimney & pipework project in...
SCR Technology for Police Vessel SCR Technology for Police Vessel
  IMS supplied its “Modular Reactor” in conjunction with the “Detronic&rd...
6 SCR Systems for Overseas Client 6 SCR Systems for Overseas Client
IMS designed and supplied six SCR systems for an overseas client in 2017. The emissions target w...
SCR Technology for UK Airport SCR Technology for UK Airport
IMSeco designed and manufactured a range of “SCRT” (SCR+DPF) systems which was shippe...
Full Acoustic Project at UK Hospital Full Acoustic Project at UK Hospital
IMS have just completed on this epic acoustic project at Northampton General Hospital. Our remit ...
Exhaust Silencers Exhaust Silencers
The New Doha International Airport in Qatar is (NDIA) using Eight 36" nominal bore reactive / abs...